SDF no4 (US blanks green Pu 5.10RP)

What works and what doesn't. Share design ideas, references and contacts for paipo board builders.
User avatar
nomastomas
Big Wave Charger
Posts: 597
Joined: Thu Nov 17, 2011 2:30 am
City: Ojai
State or Province: CA
Country: USA
Interests: Surfing, cycling and fishing
Location: Ojai, CA
Contact:

Re: SDF no4 (US blanks green Pu 5.10RP)

#21

Unread post by nomastomas »

How much rocker in your present design? With the right combination of bottom curve and fin size (small), its pretty easy to release the fins (TBG4: NR=2.75, TR=0 .75). I've done inadvertent 180s when kicking out while riding in a forward position. I suspect with a little practice a 360 is possible.
"This is a paipo site...isn't it?"
www.tp4surf.com
User avatar
krusher74
Big Wave Charger
Posts: 842
Joined: Wed Nov 07, 2012 3:53 pm
City: easkey
State or Province: co sligo
Country: Ireland
Interests: Surfing, vintage cars and motorbikes
Location: Easky, Co sligo , ireland
Contact:

Re: SDF no4 (US blanks green Pu 5.10RP)

#22

Unread post by krusher74 »

nomastomas wrote:How much rocker in your present design? With the right combination of bottom curve and fin size (small), its pretty easy to release the fins (TBG4: NR=2.75, TR=0 .75). I've done inadvertent 180s when kicking out while riding in a forward position. I suspect with a little practice a 360 is possible.
Its about 3" nose 1/2" tail (more in centre with open concave)

I had tiny knubsters fins on my endeavour board as an experiment. Only about an inch deep. Surfed on them for a few months and could still 360. Then took them out one day and the board felt much faster without them (with them was like driving a car with the parking break left on a little) and 360's now spun much faster.

I don't think the benefit of fins will ever outweigh their drawbacks for me personally. :cry:

I will take this as the experiment it was and go back to my chine rail next time, it has more bite and drive. I guess it acts like a long fin? At least I now know how they both act. Hopefully I can somewhat sand off any release edge there is in the last 12" of the rail to see how much more traction that gives.

Are you still going to make your finless board Thomas?
Pes78
Big Wave Charger
Posts: 276
Joined: Wed Jan 07, 2015 1:39 am
City: San Diego
State or Province: CALIFORNIA
Country: United States

Re: SDF no4 (US blanks green Pu 5.10RP)

#23

Unread post by Pes78 »

Hey krusher when shaped the board did you feel the foam getting softer? I just ordered another blank in green density and lowered the tail rocker a 1/2".

Paul
User avatar
nomastomas
Big Wave Charger
Posts: 597
Joined: Thu Nov 17, 2011 2:30 am
City: Ojai
State or Province: CA
Country: USA
Interests: Surfing, cycling and fishing
Location: Ojai, CA
Contact:

Re: SDF no4 (US blanks green Pu 5.10RP)

#24

Unread post by nomastomas »

Keith...that project always gets moved to the back-burner. I like what Ekstrom has done with bottom and rail contours. But with El Nino just around the corner, I'm currently focused on building a p-board ("prone board" is what Buzzy Kneubuhl calls sandwich construction paipos. I like it!) that performs well in OH waves. I plan to increase the length to 50" or 52", adjusting outline and foil to maximize flat out speed. Both thickness and wide-point will be slightly forward of center. Key will be designing a board that has sufficient volume to really plane well but can still duck dive easily. Bottom will be deep single concave a la Maurice Cole's work. Just have to work out hand placement. I like the forward "bumps" of Gus Acosta's Wave Arrow, but I'm also considering a modification of the "pickle-fork" nose seen on the Gemini shapes. I think that would help to keep the elbows on the deck, away from the rail. Fins of course, either full-sized 5.25" twinnies with 1/8" toe-in and 7-deg cant, or quad with M7/AM2 fronts and a pair of AM2 center fins for rears, set using McKee's formula. I've got a couple of months to work out the details...
"This is a paipo site...isn't it?"
www.tp4surf.com
jbw4600
Big Wave Charger
Posts: 289
Joined: Sat Nov 05, 2011 6:08 pm
City: Kentfield
State or Province: CA
Country: USA
Location: Fairfax, CA
Contact:

Re: SDF no4 (US blanks green Pu 5.10RP)

#25

Unread post by jbw4600 »

Keith, If you decide to put fins on it, you might try putting some Grom sized thruster side fins. They have low surface area and are pointy. Pointy fins pivot better than the those keel like fins.
User avatar
nomastomas
Big Wave Charger
Posts: 597
Joined: Thu Nov 17, 2011 2:30 am
City: Ojai
State or Province: CA
Country: USA
Interests: Surfing, cycling and fishing
Location: Ojai, CA
Contact:

Re: SDF no4 (US blanks green Pu 5.10RP)

#26

Unread post by nomastomas »

BTW, where did you place the fins? How much toe-in? Cant?
"This is a paipo site...isn't it?"
www.tp4surf.com
User avatar
bgreen
Big Wave Charger
Posts: 1232
Joined: Fri Aug 19, 2011 5:17 pm
City: Brisbane
State or Province: Qld
Country: Oz
Contact:

Re: SDF no4 (US blanks green Pu 5.10RP)

#27

Unread post by bgreen »

Patrick,

The new board sounds interesting. When will it be on view?

Bob
User avatar
nomastomas
Big Wave Charger
Posts: 597
Joined: Thu Nov 17, 2011 2:30 am
City: Ojai
State or Province: CA
Country: USA
Interests: Surfing, cycling and fishing
Location: Ojai, CA
Contact:

Re: SDF no4 (US blanks green Pu 5.10RP)

#28

Unread post by nomastomas »

Bob...its still in my head, but soon I should have some drawings to share
"This is a paipo site...isn't it?"
www.tp4surf.com
User avatar
krusher74
Big Wave Charger
Posts: 842
Joined: Wed Nov 07, 2012 3:53 pm
City: easkey
State or Province: co sligo
Country: Ireland
Interests: Surfing, vintage cars and motorbikes
Location: Easky, Co sligo , ireland
Contact:

Re: SDF no4 (US blanks green Pu 5.10RP)

#29

Unread post by krusher74 »

Pes78 wrote:Hey krusher when shaped the board did you feel the foam getting softer? I just ordered another blank in green density and lowered the tail rocker a 1/2".

Paul
The Green foam seemed to stay firm as I got deeper, but i dont have much foam/shaping experience :? , definitely firmer that a previous blue blank
User avatar
krusher74
Big Wave Charger
Posts: 842
Joined: Wed Nov 07, 2012 3:53 pm
City: easkey
State or Province: co sligo
Country: Ireland
Interests: Surfing, vintage cars and motorbikes
Location: Easky, Co sligo , ireland
Contact:

Re: SDF no4 (US blanks green Pu 5.10RP)

#30

Unread post by krusher74 »

nomastomas wrote:BTW, where did you place the fins? How much toe-in? Cant?
dont know the numbers but here is a pic, rear most position was the only place i vaguely liked
Attachments
test.JPG
test.JPG (158.49 KiB) Viewed 4190 times
User avatar
krusher74
Big Wave Charger
Posts: 842
Joined: Wed Nov 07, 2012 3:53 pm
City: easkey
State or Province: co sligo
Country: Ireland
Interests: Surfing, vintage cars and motorbikes
Location: Easky, Co sligo , ireland
Contact:

Re: SDF no4 (US blanks green Pu 5.10RP)

#31

Unread post by krusher74 »

Ride report update!

Well today I was looking at the board and it had a hard edge on the back 3rd of the rail and a faint hard edge as far as two 3rds up, so I got the sandpaper out and sanded all off. :?

Result hold and drive is back! totally changed the board :D

I was doing hard bottom turns and S turn cut backs with ease today, so the hard edge is only across the tail now. Interestingly 360's now spin round a little slower.

Now totally stocked with how this board surfs, 8-)

Put a cork deck pad on too.
Attachments
2015-11-002.jpg
2015-11-002.jpg (112.66 KiB) Viewed 4517 times
User avatar
nomastomas
Big Wave Charger
Posts: 597
Joined: Thu Nov 17, 2011 2:30 am
City: Ojai
State or Province: CA
Country: USA
Interests: Surfing, cycling and fishing
Location: Ojai, CA
Contact:

Re: SDF no4 (US blanks green Pu 5.10RP)

#32

Unread post by nomastomas »

Yes, a hard edge promotes water release. Softening the rail edge, encourages water to rap around and "grip" the rail. This was the lesson learned from the 70s down-rail mini-guns. The early down-railers were fast, but prone to spin-out. The introduction of rail fins was an attempt to counter the spin-out while keeping the speed. I would think a soft edge or no edge rail would be important on a finless board. The softer-but-stickier rail you now have may explain the slower 360s. Water just doesn't break away from the rail as quickly.
"This is a paipo site...isn't it?"
www.tp4surf.com
User avatar
patrickSAWBOARDS
Wave slider
Posts: 6
Joined: Tue Jun 17, 2014 5:16 am
City: Narberth
State or Province: Pembrokeshire
Country: United Kingdom
Location: Pembrokeshire, West Wales
Contact:

Re: SDF no4 (US blanks green Pu 5.10RP)

#33

Unread post by patrickSAWBOARDS »

Hey Keith, The board looks amazing. Hope you have been enjoying the recent swell. Looks like we might get a bit more winter next week! Fingers crossed. See you soon.
User avatar
krusher74
Big Wave Charger
Posts: 842
Joined: Wed Nov 07, 2012 3:53 pm
City: easkey
State or Province: co sligo
Country: Ireland
Interests: Surfing, vintage cars and motorbikes
Location: Easky, Co sligo , ireland
Contact:

Re: SDF no4 (US blanks green Pu 5.10RP)

#34

Unread post by krusher74 »

Got a few waves on the board today with my buddy on his bodyplane, these are the more flat weak local waves I designed this board for and the extra wide wide point forward is working out good for getting forward on the board to promote speed on flat sections.
Attachments
IMG_9284.JPG
IMG_9284.JPG (62.97 KiB) Viewed 4491 times
IMG_9456.JPG
IMG_9456.JPG (36.54 KiB) Viewed 4491 times
IMG_9308.JPG
IMG_9308.JPG (30.45 KiB) Viewed 4491 times
User avatar
bgreen
Big Wave Charger
Posts: 1232
Joined: Fri Aug 19, 2011 5:17 pm
City: Brisbane
State or Province: Qld
Country: Oz
Contact:

Re: SDF no4 (US blanks green Pu 5.10RP)

#35

Unread post by bgreen »

Keith,

Is this the place we surfed on that small onshore day? There is some interesting footage of smaller handplanes in Hawaii getting some impressive lift.

Bob
User avatar
nomastomas
Big Wave Charger
Posts: 597
Joined: Thu Nov 17, 2011 2:30 am
City: Ojai
State or Province: CA
Country: USA
Interests: Surfing, cycling and fishing
Location: Ojai, CA
Contact:

Re: SDF no4 (US blanks green Pu 5.10RP)

#36

Unread post by nomastomas »

I like photos of p-boards on clean, little waves. The scale is just right.
"This is a paipo site...isn't it?"
www.tp4surf.com
User avatar
krusher74
Big Wave Charger
Posts: 842
Joined: Wed Nov 07, 2012 3:53 pm
City: easkey
State or Province: co sligo
Country: Ireland
Interests: Surfing, vintage cars and motorbikes
Location: Easky, Co sligo , ireland
Contact:

Re: SDF no4 (US blanks green Pu 5.10RP)

#37

Unread post by krusher74 »

bgreen wrote:Keith,

Is this the place we surfed on that small onshore day? There is some interesting footage of smaller handplanes in Hawaii getting some impressive lift.

Bob
No this is Sker, the one you came to that was 4ft plus that early morning when you were in cardiff. :D
User avatar
bgreen
Big Wave Charger
Posts: 1232
Joined: Fri Aug 19, 2011 5:17 pm
City: Brisbane
State or Province: Qld
Country: Oz
Contact:

Re: SDF no4 (US blanks green Pu 5.10RP)

#38

Unread post by bgreen »

I really wish I'd walked back down that track and taken some waves photos. As tough as the sand walk was it would have been way more fun than doing circles are cardiff with a dying GPS.

It's funny how those two waves look so different - the top a bit crumbly but the bottom one does look like S. Those inside boulders were a killer.

Bob
User avatar
krusher74
Big Wave Charger
Posts: 842
Joined: Wed Nov 07, 2012 3:53 pm
City: easkey
State or Province: co sligo
Country: Ireland
Interests: Surfing, vintage cars and motorbikes
Location: Easky, Co sligo , ireland
Contact:

Re: SDF no4 (US blanks green Pu 5.10RP)

#39

Unread post by krusher74 »

Got some shots of me on this board at a local reef break last week, was trying to do some stand up surfer style off the tops, surprised from the photos how in the lip i got as finless and print this 180 turn is hard. still enjoying and using this board regularly. The green foam, 6oz, 4/6oz top had held up very well.
Attachments
1-001.jpg
1-001.jpg (19.06 KiB) Viewed 4047 times
2-001.jpg
2-001.jpg (20.61 KiB) Viewed 4047 times
3-001.jpg
3-001.jpg (15.87 KiB) Viewed 4047 times
4-001.jpg
4-001.jpg (24.04 KiB) Viewed 4047 times
User avatar
nomastomas
Big Wave Charger
Posts: 597
Joined: Thu Nov 17, 2011 2:30 am
City: Ojai
State or Province: CA
Country: USA
Interests: Surfing, cycling and fishing
Location: Ojai, CA
Contact:

Re: SDF no4 (US blanks green Pu 5.10RP)

#40

Unread post by nomastomas »

You have a good photog. Seems to know what would make a good surfing action shot. Board seems to be working pretty well, too.
"This is a paipo site...isn't it?"
www.tp4surf.com
Post Reply

Who is online

Users browsing this forum: No registered users and 42 guests