4'10
-
- Big Wave Charger
- Posts: 276
- Joined: Wed Jan 07, 2015 1:39 am
- City: San Diego
- State or Province: CALIFORNIA
- Country: United States
4'10
Have a board in the works being shaped by Tony Caramagna of TC Surfboards. Tony grew up in the Point Loma and Sunset Cliffs area here in San Diego and has made kneeboards before. He is very easy to work with and I feel I was able to tell him what I have trying to do in my shaping. He was very open to trying out something like this. The concave isn't very deep 3/4" of an inch in the center. The thickness out at the rails is 2.5" and the width is 22" wide. Length is 4'10" and he put his channel fish bottom on it. It has about a .25" concave running the length of the board going into a double through the fins, have it set up as a quad. Will ride this prone as well, just not feeling the shaping anymore. Trying to have a one board quiver which I know is impossible but with what I have planned for the future I may not have the space for multiple boards.
- nomastomas
- Big Wave Charger
- Posts: 597
- Joined: Thu Nov 17, 2011 2:30 am
- City: Ojai
- State or Province: CA
- Country: USA
- Interests: Surfing, cycling and fishing
- Location: Ojai, CA
- Contact:
Re: 4'10
Interesting...do you have a shot of the bottom?
"This is a paipo site...isn't it?"
www.tp4surf.com
www.tp4surf.com
- rodndtube
- Big Wave Charger
- Posts: 1158
- Joined: Thu Aug 18, 2011 10:34 pm
- City: Arbutus Land
- State or Province: Maryland
- Country: USA
- Interests: Waveriding, travel and the Paipo Research Project
- Location: Maryland, USA & Where the Waves Are Breaking
- Contact:
Re: 4'10
Photo angles can be so deceiving... looks like a round bottom to me!
rodNDtube
"Prone to ride"
I love my papa li`ili`i
"The sea doth wash away all human ills."
-- Euripides.
"Prone to ride"
I love my papa li`ili`i
"The sea doth wash away all human ills."
-- Euripides.
-
- Big Wave Charger
- Posts: 384
- Joined: Sat Sep 17, 2011 9:58 am
- City: Paonia
- State or Province: Colorado
- Country: USA
- Location: Paonia, Colorado
- Contact:
Re: 4'10
Looks to me as if it is on the racks w/ deck down so round deck and complex concave within a concave bottom
- nomastomas
- Big Wave Charger
- Posts: 597
- Joined: Thu Nov 17, 2011 2:30 am
- City: Ojai
- State or Province: CA
- Country: USA
- Interests: Surfing, cycling and fishing
- Location: Ojai, CA
- Contact:
-
- Big Wave Charger
- Posts: 276
- Joined: Wed Jan 07, 2015 1:39 am
- City: San Diego
- State or Province: CALIFORNIA
- Country: United States
Re: 4'10
Running it as a quad but wouldn't be opposed to going finless. Getting a set of the Lovelace Piggyback quads.
https://goo.gl/images/3R8vKL
https://goo.gl/images/3R8vKL
- krusher74
- Big Wave Charger
- Posts: 842
- Joined: Wed Nov 07, 2012 3:53 pm
- City: easkey
- State or Province: co sligo
- Country: Ireland
- Interests: Surfing, vintage cars and motorbikes
- Location: Easky, Co sligo , ireland
- Contact:
Re: 4'10
I feel like the concave deck makes a ridge outside of it on the rail, riding finless i'm usually over right on the rail, with my hip and elbow, would be interesting to see this ridden. I guess it would be more like greenough on a spoon.
What's the board thickness in the middle?
What's the board thickness in the middle?
http://www.sdfsurfboards.co.uk/ built my paipo!
-
- Big Wave Charger
- Posts: 276
- Joined: Wed Jan 07, 2015 1:39 am
- City: San Diego
- State or Province: CALIFORNIA
- Country: United States
Re: 4'10
I'll be putting a cove pad on it so I'd be pretty locked in. The Greenough thing is what I'm kinda going for. I would like to get some footage if me surfing it at some point. Thickness is 1.5" in the center, the concave deck is .75" and the bottom has .25" single before it goes into the double through the tail. Have to wait a couple more weeks to get this thing in the water.
-
- Big Wave Charger
- Posts: 384
- Joined: Sat Sep 17, 2011 9:58 am
- City: Paonia
- State or Province: Colorado
- Country: USA
- Location: Paonia, Colorado
- Contact:
Re: 4'10
In films and stills it looks to me as if GG has his knees/shins very far apart, sort of wedged against the inner edges of the extreme concave on Velo. And given the amount of roll (how up on a rail he would get) there would be a lot of force driving the rail down into the wave face, much like prone with hip and elbow on the railkrusher74 wrote:I feel like the concave deck makes a ridge outside of it on the rail, riding finless i'm usually over right on the rail, with my hip and elbow, would be interesting to see this ridden. I guess it would be more like greenough on a spoon.
What's the board thickness in the middle?
-
- Big Wave Charger
- Posts: 340
- Joined: Sun Dec 28, 2014 2:48 pm
- City: Durban
- State or Province: Natals
- Country: South Africa
Re: 4'10
I was trying to explain that moving the hips away from the rail wash, out of the high pressure to low pressure curl. And how your hip affects fluid attachment to the inside tail rail area. I use foam ribs on my boards to place my hips out of the wave face
- bgreen
- Big Wave Charger
- Posts: 1232
- Joined: Fri Aug 19, 2011 5:17 pm
- City: Brisbane
- State or Province: Qld
- Country: Oz
- Contact:
Re: 4'10
On my latest board I noticed some drag from my body at various times. When I slightly altered my body position I noticed a small but noticeable burst of speed. On another board it was my elbow that was dragging, which resulted in spray to my face.
Lifting one leg also altered dynamics, to slightly readjust weight.
An interesting feature of Keith's board is the thickness - overall the board is intended to replicate a boogie board design so it is shorter and thicker than the boards I ride.
Lifting one leg also altered dynamics, to slightly readjust weight.
An interesting feature of Keith's board is the thickness - overall the board is intended to replicate a boogie board design so it is shorter and thicker than the boards I ride.
- nomastomas
- Big Wave Charger
- Posts: 597
- Joined: Thu Nov 17, 2011 2:30 am
- City: Ojai
- State or Province: CA
- Country: USA
- Interests: Surfing, cycling and fishing
- Location: Ojai, CA
- Contact:
Re: 4'10
The "G" variants have the wide point below center to keep the hips out of the water and a square or diamond nose to encourage a board holding position that places the arms/elbows on the deck, away from the wave face. Plus a deck concave to help keep the rider centered on the deck. I actually try to use a tailblock width equal to the riders hip width plus 1". Object = Nothing in the water but the board.
"This is a paipo site...isn't it?"
www.tp4surf.com
www.tp4surf.com
Who is online
Users browsing this forum: No registered users and 1 guest